what servo ? ?

Register

we are looking to upgrade my servo we have already got a futaba s9550 steering speed is o.11 i feel i need more steering speed as im allways increasing my steering punch.
any ideas would be greatful.

_________________
sponserd by :
Kifopaint.
Drives .........
Xray T3 && T2 009 =]

this is the one im using

http://www.microtechracing.com//p...;Pcat=RADIO%20GEAR&cat=SERVOS

i got mine for 60 pound from speedtech rc but they are sold out at mo.

this one replaces the one u have already i think trev have one

http://www.microtechracing.com//p...;Pcat=RADIO%20GEAR&cat=SERVOS

Yer I do have the one Mark said I have the 9551 which is 0.11s @ 6v BUT I don't run it any more as it was not quick enough I have gone back to my old KO 2343 High Speed 0.08s @ 6v FAST , Sounds silly But you can feel the difference , The KO may be old and BIG But its Fast ....

This one is worth taking a chance on REMEMBER its rated at 4.8v when you look at the Spec and Nick tells me he has had good feedback on them .........

For what they cost if its no quicker its a Good price for a spare in the pit box anyway .....

http://demonpowerproducts.co.uk/p...?cPath=25_54&products_id=3124

Maybe when you drove my car Sunday Ben it was the SERVO you liked not the CAR

_________________
Sponsored By Demon Products - Schumacher UK - Titanium Racing

Numb Nuts Tri Club 2007 / 2008 Pro Stock Champion 2008 / 2009 Numb nuts open Champion , 2008 CMCRC Brushless Champion , 2008 CMCRC Open Champion , Ansmann GP Stock Vice Champion 2009

.

Ive got one of these as a spare/waiting to go in a car and im also running the full length version in my b4 and they are very fast for the price. They also look pretty good with the transparent cases. You can see all of the gears going round as well.

Gee whizz you've got good eyesight, I have difficulty seeing the car go round the track without concentrating on the gears in the servo!

One thing you need to remeber when comparing servos is to check what voltage the BEC in your speedo is giving out - it could be 4.8, 6.0 or 7.2 volts, and that will hjave a big impact on the speed of the servo.

For Futaba if you go to:-

www.futaba-rc.com

there is a chart that gives the performance parameters of all their servos and there is only one (for helicopters) that is faster than 0.11.

_________________
Beauty is in the eye of the beer holder!

I use the KO low profile servo which I find is more than adequate for my use, I also have a 2365 ultra fast KO unit, this is the mutts nuts on speed, and I have had to turn it down so that I can keep up with it. However the one I am running in the new car is the KO low profile unit.

Great servo I've had two now and they have been faultless.

_________________
The only law is the Captains Law, and Tamiya is the Daddy, everything else is a very poor second.

I also run the Low profile KO unit. Was infact one that Trev sold me some time back now. Its a fantastic little unit and hasnt missed a beat since ive had it.

_________________
Sponsored By Serpent UK

I wish I had never sold it to you Jim ,,, Can't remember why I did I think I needed the money as I am sure it was Brand new q11

_________________
Sponsored By Demon Products - Schumacher UK - Titanium Racing

Numb Nuts Tri Club 2007 / 2008 Pro Stock Champion 2008 / 2009 Numb nuts open Champion , 2008 CMCRC Brushless Champion , 2008 CMCRC Open Champion , Ansmann GP Stock Vice Champion 2009

.

I use the KO 2343 as it's just so fast.

leigh has lent me his super fast servo q15

to try tomorrow . Beware

_________________
sponserd by :
Kifopaint.
Drives .........
Xray T3 && T2 009 =]